191 raystar raystar optronics,inc. oled graphic type absolute maximum rating electronical characteristics mechanical data feature dimension drawing RET012864C oled graphic 128x64 dots 14.80.5 14.50 active area 128*64 pixels 69.852.0 28.00 61.30 11.50 2.0 2.0max 36.500 2-?1.0 0.30.05 39.86 41.860.2 73.000.2 61.41(aa) 30.69(aa) 32.69(va) 63.41(va) 5.795 4.795 3.190 2.190 2.0 view direction active area 128*64 pixels view direction 82.7000.2 89.7000.2 40.2000.2 47.2000.2 ?3.2 ?7.0 3.400 11.50.2 w=0.3 p0.5*21=10.5 0.5 1 22 1 31 nc vcc vcomh iref d7 d6 d5 d4 d3 d2 d1 d0 e/rd r/ w d/c re s cs fr bs2 bs1 vddi o vd d vcir bggnd vbre f nc fb vddb gd r vss nc contct size 5.00.5 icssd1305t7 single tape teraoka 631s 27*8*0.085mm double tape tesa 4972 22*6*0.05mm seal.white 1 22 scale 1:2 detail dots scale 1:10 0.45 0.48 0.48 0.45 1. 128 x 64 dots 2. built-in controller ssd1305t7r1 3. +3v power supply 4. 1/64 duty cycle 5. interface: 6800, 8080, spi, i2c 6. polarizer optional description symbol no. pin power supply for analog circuit. com voltage output. a capacitor should be connected between this pin and vss. reference current input pin. a resistor should be connected between this pin and vss. data bus. data read operation is initiated when its pull low. data write operation is initiated when its pull low. data/ command control. pull high for write/read display data. pull low for write command or read status. reset signal input. when its low, initialization of ssd1305 is executed. chip select input. communicating protocol select these pins are mcu interface selection input. see the following table: 68xx-parallel 80xx-parallel serial bs1 0 1 0 bs2 1 1 0 power supply for logic circuit. no connection. ground. ground. vcc vcomh iref d7~d0 e/rd# r/w# d/c# res# cs# bs2 bs1 vdd nc vss vss 1 2 3 4~11 12 13 14 15 16 17 18 19 20 21 22 item module dimension active area view area dot pitch dot size mounting hole dimension 89.7 47.2 3.4 61.41 30.69 82.7 40.2 63.41 x 32.69 0.45 0.45 0.48 0.48 unit mm mm mm mm mm mm min -0.3 8 max 3.5 16 unit v v notes 1, 2 1, 2 parameter supply voltage for logic supply voltage for display symbol vdd vcc characteristics supply voltage for logic supply voltage for display high level output low level lutput operating current for vdd operating current for vcc sleep mode current for vdd sleep mode current for vcc high level input low level input symbol vdd vcc vih vil voh vol idd icc idd, sleep icc, sleep min 2.4 14.5 0.8vdd 0 0.9vdd 0 - - typ 2.7 15 - - - - - - max 3.5 15 vdd 0.2vdd vdd 0.1vdd 10 10 unit v v v v v v a a conditions - - iout= 100a, 3.3mhz iout= 100a, 3.3mhz iout= 100a, 3.3mhz iout= 100a, 3.3mhz note 4 note 5 250 250 400 400 a a ma ma - - - - note 4 note 5 31 53 39 66 note 3: brightness (l br ) and supply voltage for display (v cc ) are subject to the change of the panel characteristics and the customers request. note 4: v dd = 2.7v, v cc = 15v, 50% display area turn on. note 5: v dd = 2.7v, v cc = 15v, 100% display area turn on. raystar optronics, inc.
|
